Configuring GTP on FortiOS Carrier

Configuring GTP support on FortiOS Carrier involves configuring a number of areas of features. Some features require longer explanations, and have their own chapters. The other features are addressed here.

• GTP support on the Carrier-enabled FortiGate unit
• Configuring General Settings on the Carrier-enabled FortiGate unit
• Configuring Encapsulated Filtering in FortiOS Carrier Configuring the Protocol Anomaly feature in FortiOS Carrier Configuring Anti-overbilling in FortiOS Carrier
• Logging events on the Carrier-enabled FortiGate unit

 

GTP support on the Carrier-enabled FortiGate unit

The FortiCarrier unit needs to have access to all traffic entering and exiting the carrier network for scanning, filtering, and logging purposes. This promotes one of two configurations — hub and spoke, or bookend.

A hub and spoke configuration with the Carrier-enabled FortiGate unit at the hub and the other GPRS devices on the spokes is possible for smaller networks where a lower bandwidth allows you to divide one unit into multiple virtual domains to fill multiple roles on the carrier network. It can be difficult with a single FortiOS Carrier as the hub to ensure all possible entry points to the carrier network are properly protected from potential attacks such as relayed network attacks.

A bookend configuration uses two Carrier-enabled FortiGate units to protect the carrier network between them with high bandwidth traffic. One unit handles traffic from mobile stations, SGSNs, and foreign carriers. The other handles GGSN and data network traffic. Together they ensure the network is secure.

The Carrier-enabled FortiGate unit can access all traffic on the network. It can also verify traffic between devices, and verify that the proper GPRS interface is being used. For example there is no reason for a Gn interface to be used to communicate with a mobile station — the mobile station will not know what to do with the data — so that traffic is blocked.

When you are configuring your Carrier-enabled FortiGate unit’s GTP profile, you must first configure the APN. It is critical to GTP communications — no traffic will flow without the APN.

 

The Carrier-enabled FortiGate unit does more than just forward and route GTP packets over the network. It also performs:

• Packet sanity checking
• GTP stateful inspection
• Protocol anomaly detection and prevention
• HA
• Virtual domain support

Sending administrator alert notifications

When duplicate messages are detected, the Carrier-enabled FortiGate unit can be configured to notify you immediately with an MMS message. Enable this feature by selecting Alert Notification in the duplicate message action. Each duplicate message threshold can be configured separately.

 

Configuring how and when to send alert notifications

You can configure different alert notifications for MM1 and MM4 duplicate messages. You can configure the FortiOS Carrier unit to send these alert notifications using the MM1, MM3, MM4, or MM7 content interface. Each of these content interfaces requires alert notification settings that the FortiOS Carrier unit uses to communicate with a server using the selected content interface.

For the MM1 content interface you require:

• The hostname of the server
• The URL of the server (usually “/”)
• The server port (usually 80)

For the MM3 and MM4 content interfaces you require:

• The hostname of the server l  The server port (usually 80) l  The server user domain For the MM7 content interface you require:
• The message type
• submit.REQ to send a notification message to the sender in the form of a submit request. The message goes from a VAS application to the MMSC.
• deliver.REQ to send a notification message to the sender in the form of a deliver request. The message goes from the MMSC to a VAS application.
• The hostname of the server
• The URL of the server (usually “/”)
• The server port (usually 80)
• A user name and password to connect to the server
• The value-added-service-provider (VASP) ID
• The value-added-service (VAS) ID

 

To configure administrator alert notifications – web-based manager

1. Go to Security Profiles > MMS Profile and edit or add a new MMS protection profile.

2. Expand MMS Bulk Email Filtering Detection.

There are three duplicate message thresholds.

3. Expand the threshold that you want to configure alert notification for.

4. For Duplicate Message Action, select the Alert Notification check box. Alert notification options appear.

5. For the Source MSISDN, enter the MSISDN from which the alert notification message will be sent.

6. Select the Message Protocol the alert notification will use: MM1, MM3, MM4, or MM7.

7. Add the information required by FortiOS Carrier to send messages using the selected message protocol:

8. For Notifications Per Second Limit, enter the number of notifications to send per second.

Use this setting to reduce control the number of notifications sent by the FortiOS Carrier unit. If you enter zero (0), the notification rate is not limited.

9. If required, change Window Start Time and Window Duration configure when the FortiOS Carrier unit sends alert notifications.

By default, notifications are sent at any time of the day. You can change the Window Start Time if you want to delay sending alert messages. You can also reduce the Window Duration if you want to stop sending alert notifications earlier.

For example, you might not want FortiOS Carrier sending notifications except during business hours. In this case the Window Start Time could be 9:00 and the Window Duration could be 8:00 hours.

You can set different alert notifications for each message threshold. For example, you could limit the message window for lower thresholds and set it to 24 hours for higher thresholds. This way administrators will only receive alert notifications outside of business hours for higher thresholds.

10. For Day of Week, select the days of the week to send notifications.

For example, you may only want to send alert notifications on weekends for higher thresholds.

11. In the Interval field, enter the maximum frequency that alert notification messages will be sent, in minutes or hours.

All alerts occurring during the interval will be included in a single alert notification message to reduce the number of alert messages that are sent.

 

Configuring who to send alert notifications to

In each MMS protection profile you add a list of recipient MSISDNs. For each of these MSISDNs you select the duplicate threshold that triggers sending notifications to this MSISDN.

 

To configure the alert notification recipients – web-based manager

1. Go to Security Profiles > MMS Profile.

2. Select the Edit icon of the MMS profile in which you want to configure the alert notification recipients.

3. Expand MMS Bulk Email Filtering Detection.

4. Expand Recipient MSISDN.

5. Select Create New.

6. In the New MSISDN window, enter the MSISDN to use for duplicate threshold alert notification. Select the duplicate thresholds at which to send alert notifications to the MSISDN.

 

For the duplicate threshold to be able to send an alert notification to the MSISDN, the duplicate message threshold alert notification action must be enabled and configured.

 

Notifying duplicate message senders and receivers

The FortiOS Carrier unit does not send notifications to the sender or receiver of duplicate messages. If the sender or receiver is an attacker and is explicitly informed that they have exceeded a message threshold, the attacker may try to determine the exact threshold value by trial and error and then find a way around duplicate message protection. For this reason, no notification is set to the sender or receiver.

However, the FortiOS Carrier unit does have replacement messages for sending reply confirmations to MM1 senders and receivers and for MM4 senders for blocked messages identified as duplicate messages. For information about how FortiOS Carrier responds when message flood detection blocks a message, see and MMS duplicate messages and message floods.

 

Responses to MM1 senders and receivers

When the FortiOS Carrier unit identifies an MM1 message sent by a sender to an MMSC as a duplicate message and blocks it, the FortiOS Carrier unit returns a message submission confirmation (m-send.conf) to the sender (otherwise the sender’s handset would keep retrying the message). The m-send.conf message is sent only when the MM1 duplicate message action is set to Block. For other duplicate message actions the message is actually delivered to the MMSC and the MMSC sends the m-send.conf message.

You can customize the m-send.conf message by editing the MM1 send-conf duplicate message MM1 replacement message (from the CLI the mm1-send-conf-dupe replacement message). You can customize the response status and message text for this message. The default response status is “Content not accepted”. To hide the fact that the FortiOS Carrier unit is responding to a duplicate message, you can change the response status to “Success”. The default message text informs the sender that the message was blocked. You could change this to something more generic.

For example, the following command sets the submission confirmation response status to “Success” and changes the message text to “Message Sent OK”:

config system replacemsg mm1 mm1-send-conf-dupe set rsp-status ok

set rsp-text “Message Sent OK”

end

When the FortiOS Carrier unit identifies an MM1 message received by a receiver from an MMSC as a duplicate message and blocks it, the FortiOS Carrier unit returns a message retrieval confirmation (m-retrieve.conf) to the sender (otherwise the sender’s handset would keep retrying). The m-retrieve.conf message is sent only when the MM1duplicate message action is set to Block. For other message flood actions the message is actually received by the receiver, so the MMSC sends the m-retrieve.conf message.

You can customize the m-retrive.conf message by editing the MM1 retrieve-conf duplicate message MM1 replacement message (from the CLI the mm1-retr-conf-dupe replacement message). You can customize the class, subject, and message text for this message.

For example, you could use the following command make the response more generic:

config system replacemsg mm1 mm1-retr-conf-dupe set subject “Message blocked”

set message “Message temporarily blocked by carrier”

end

 

Forward responses for duplicate MM4 messages

When the FortiOS Carrier unit identifies an MM4 message as a duplicate message and blocks it, the FortiOS Carrier unit returns a message forward response (MM4_forward.res) to the forwarding MMSC (otherwise the forwarding MMSC would keep retrying the message). The MM4_forward.res message is sent only when the MM4 duplicate message action is set to Block and the MM4-forward.req message requested a response. For more information, see and MMS duplicate messages and message floods.

You can customize the MM4_forward.res message by editing the MM4 duplicate message MM4 replacement message (from the CLI the mm4-dupe replacement message). You can customize the response status and message text for this message. The default response status is “Content not accepted” (err-content-not- accept). To hide the fact that the FortiOS Carrier unit is responding to a duplicate message, you can change the response status to “Success”. The default message text informs the sender that the message was blocked. You could change this to something more generic.

For example, the following command sets the submission confirmation response status to “Success” and changes the message text to “Message Forwarded OK”:

config system replacemsg mm4 mm4-dupe set rsp-status ok

set rsp-text “Message Forwarded OK”

end

 

Viewing DLP archived messages

If DLP Archive is a selected duplicate message action, the messages that exceed the threshold are saved to the MMS DLP archive. The default behavior is to save all of the offending messages but you can configure the DLP archive setting to save only the first message that exceeds the threshold. See Viewing DLP archived messages.

Order of operations: flood checking before duplicate checking

Although duplicate checking involves only examination and comparison of message contents and not the sender or recipient, and flood checking involves only totalling the number of messages sent by each subscriber regardless of the message content, there are times when a selection of messages exceed both flood and duplicate thresholds.

The Carrier-enabled FortiGate unit checks for message floods before checking for duplicate messages. Flood checking is less resource-intensive and if the flood threshold invokes a Block action, the blocked messages are stopped before duplicate checking occurs. This saves both time and FortiOS Carrier system resources.

 

Bypassing duplicate message detection based on user’s carrier endpoints

You can use carrier endpoint filtering to exempt MMS sessions from duplicate message detection. Carrier endpoint filtering matches carrier endpoints in MMS sessions with carrier endpoint patterns. If you add a carrier endpoint pattern to a filter list and set the action to exempt from mass MMS, all messages from matching carrier endpoints bypass duplicate message detection. For more information about endpoints, see FortiOS Handbook User Authentication guide.

 

Configuring duplicate message detection

To have the Carrier-enabled FortiGate unit check for duplicate messages, configure the duplicate threshold in an

MMS profile, and select the MMS profile in a security policy.

All traffic matching the security policy will be checked for duplicate messages according to the settings in the

MMS profile.

The duplicate scanner will only scan content. It will not scan headers. Content must be exactly the same. If there is any difference at all in the content, it will not be con- sidered a duplicate.

The modular nature of the profiles allows you great flexibility in how you configure the scanning options. MMS profiles can be used in any number of policies, with different GTP profiles.

In a complex configuration, there may be many security policies, each with a different MMS profile. For a simpler network, you may have many security policies all using the same MMS profile.

Duplicate message protection

The convenience offered by MM1 and MM4 messaging can be abused by users sending spam or other unwanted messages. Often, the same message will be sent by multiple subscribers. The message can be spam, viral marketing, or worm-generated messages. MMS duplicate prevention can help prevent this type of abuse by keeping track of the messages being sent.

 

Overview

• Using message fingerprints to identify duplicate messages
• Messages from any sender to any recipient Setting duplicate message thresholds Duplicate message actions
• Notifying duplicate message senders and receivers
• Viewing DLP archived messages
• Order of operations: flood checking before duplicate checking
• Bypassing duplicate message detection based on user’s carrier endpoints
• Configuring duplicate message detection
• Sending administrator alert notifications

 

Overview

Duplicate message protection for MM1 messages prevents multiple subscribers from sending duplicate messages to your MMSC. Duplicate message protection for MM4 messages prevents another service provider from sending duplicate messages from the same subscriber to your MMSC. This can help prevent a potential flood that would otherwise become widespread between carriers.

 

MM1 and MM4 duplicate message protection

The FortiOS Carrier unit keeps track of the sent messages. If the same message appears more often than the threshold value you configure, then action is taken. Possible actions are logging the duplicates, blocking or intercepting duplicate messages, archiving the duplicate messages, and sending an alert to inform an administrator that duplicates are occurring.

With this highly configurable system, you can prevent the transmission of duplicate messages when there are more than you determine is acceptable.

For detailed configuration options, see Duplicate Message.

 

Using message fingerprints to identify duplicate messages

The Carrier-enabled FortiGate unit detects duplicates by keeping a record of all the messages travelling on the network and comparing new messages to those that have already been sent.

Rather than save the messages, the FortiOS carrier creates a checksum using the message body and subject. This serves as a fingerprint to identify the message. If another message with the same message body and subject appears, the fingerprint will also be the same and the Carrier-enabled FortiGate unit will recognize it as a duplicate.

By creating and saving message fingerprints instead of saving the messages, the Carrier-enabled FortiGate unit can save resources and time.

 

Messages from any sender to any recipient

Duplicate message detection will detect duplicate messages regardless of the sender or recipient. To do this, message fingerprints are generated using only the message body and subject. The sender, recipient, and other header information is not included.

If multiple messages appear with the same subject and message body, the Carrier-enabled FortiGate unit will recognize them as being the same.

 

Setting duplicate message thresholds

The FortiOS Carrier recognizes all duplicate messages, but it will take action when it detects a volume of duplicate messages that exceed the duplicate threshold you set. The threshold defines the maximum number of duplicate messages allowed, the period during which the messages are considered, and the length of time the duplicate message can not be sent by anyone.

For example, you may determine that once a duplicate message is sent more than 300 times in an hour, any attempt to send the same duplicate message will be blocked for 30 minutes.

If a particular duplicate message exceeds the duplicate message threshold and is blocked, any further attempts to send the same message will re-start the block period.

Using the example above, if the duplicate message count exceeds the duplicate threshold, any attempt to send a copy of the duplicate message will be blocked for 30 minutes. If a subscriber tries to send a copy of the message after waiting 15 minutes, the message will be blocked and the block period will be reset to 30 minutes. The block period must expire with no attempts to send a duplicate message. Only then will a subscriber be allowed to send the message. Non-duplicate messages will not reset the block period.

 

Duplicate message actions

When the Carrier-enabled FortiGate unit detects that a duplicate message has exceeded duplicate threshold, it can take any combination of the five actions you configure for the duplicate threshold.

Action                                           Description

Log                                                  Add a log entry indicating that a duplicate message event has occurred.

You must also enable logging for MMS Scanning > Bulk Messages

in the Logging section of the MMS protection profile.

DLP Archive

All messages                    Save all the messages that exceed the duplicate threshold in the DLP archive.

First message only Save the first message to exceed the duplicate threshold in the DLP archive. Subsequent messages that exceed the duplicate threshold will not be saved.

Intercept     Messages that exceed the duplicate threshold are passed to the recip- ients, but if quarantine is enabled for intercepted messages, a copy of each message is also quarantined for later examination. If the quar- antine of intercepted messages is disabled, the Intercept action has no effect.

Block Messages that exceed the duplicate threshold are blocked and will not be delivered to the message recipients. If quarantine is enabled for blocked messages, a copy of each blocked message is quarantined for later examination.

Alert Notification                            If the duplicate threshold is exceeded, the Carrier-enabled FortiGate unit will send an MMS duplicate message notification message.

 

Sending administrator alert notifications

When message floods are detected, the Carrier-enabled FortiGate unit can be configured to notify you immediately with an MMS message. Enable this feature by selecting Alert Notification in the message flood action. Each message flood threshold can be configured separately.

 

Configuring how and when to send alert notifications

You can configure different alert notifications for MM1 and MM4 message floods. You can configure the FortiOS Carrier unit to send these alert notifications using the MM1, MM3, MM4, or MM7 content interface. Each of these content interfaces requires alert notification settings that the FortiOS Carrier unit uses to communicate with a server using the selected content interface.

For the MM1 content interface you require:

• The hostname of the server
• The URL of the server (usually “/”)
• The server port (usually 80)

 

For the MM3 and MM4 content interfaces you require:

• The hostname of the server l  The server port (usually 80) l  The server user domain For the MM7 content interface you require:
• The message type
• submit.REQ to send a notification message to the sender in the form of a submit request. The message goes from a VAS application to the MMSC.
• deliver.REQ to send a notification message to the sender in the form of a deliver request. The message goes from the MMSC to a VAS application.
• The hostname of the server
• The URL of the server (usually “/”)
• The server port (usually 80)
• A user name and password to connect to the server
• The value-added-service-provider (VASP) ID
• The value-added-service (VAS) ID

 

For more information, see MMS notifications.

 

To configure administrator alert notifications – web-based manager

1. Go to Firewall Objects > MMS Profile and edit or add a new MMS protection profile.

2. Expand MMS Bulk Email Filtering Detection.

There are three message flood thresholds.

3. Expand the threshold that you want to configure alert notification for.

4. For Message Flood Action, select the Alert Notification check box. Alert notification options appear.

5. For the Source MSISDN, enter the MSISDN from which the alert notification message will be sent.

6. Select the Message Protocol the alert notification will use: MM1, MM3, MM4, or MM7.

7. Add the information required by FortiOS Carrier to send messages using the selected message protocol:

8. For Notifications Per Second Limit, enter the number of notifications to send per second.

Use this setting to reduce control the number of notifications sent by the FortiOS Carrier unit. If you enter zero (0), the notification rate is not limited.

9. If required, change Window Start Time and Window Duration configure when the FortiOS Carrier unit sends alert notifications.

By default, notifications are sent at any time of the day. You can change the Window Start Time if you want to delay sending alert messages. You can also reduce the Window Duration if you want to stop sending alert notifications earlier.

For example, you might not want FortiOS Carrier sending notifications except during business hours. In this case the Window Start Time could be 9:00 and the Window Duration could be 8:00 hours.

You can set different alert notifications for each message threshold. For example, you could limit the message window for lower thresholds and set it to 24 hours for higher thresholds. This way administrators will only receive alert notifications outside of business hours for higher thresholds.

10. For Day of Week, select the days of the week to send notifications.

For example, you may only want to send alert notifications on weekends for higher thresholds.

11. In the Interval field, enter the maximum frequency that alert notification messages will be sent, in minutes or hours.

All alerts occurring during the interval will be included in a single alert notification message to reduce the number of alert messages that are sent.

 

Configuring who to send alert notifications to

In each MMS protection profile you add a list of recipient MSISDNs. For each of these MSISDNs you select the message flood threshold that triggers sending notifications to this MSISDN.

To configure the alert notification recipients – web-based manager

1. Go to Firewall Objects > MMS Profile.

2. Select the Edit icon of the MMS profile in which you want to configure the alert notification recipients.

3. Expand MMS Bulk Email Filtering Detection.

4. Expand Recipient MSISDN.

5. Select Create New.

6. In the New MSISDN window, enter the MSISDN to use for flood threshold alert notification.

7. Select the duplicate thresholds at which to send alert notifications to the MSISDN.

 

For the flood threshold to be able to send an alert notification to the MSISDN, the alert notification action must be enabled and configured within the flood threshold

Viewing DLP archived messages

If DLP Archive is a selected message flood action, the messages that exceed the threshold are saved to the MMS DLP archive. The default behavior is to save all of the offending messages, but you can configure the DLP archive setting to save only the first message that exceeds the threshold. This still provides a sample of the offending messages without requiring as requiring as much storage.

 

To select only the first message in a flood for DLP archiving – web-based manager

1. Go to Security Profiles > Carrier > MMS Profile.

2. Edit an existing MMS Profile.

3. Expand the MMS Bulk Email Filtering Detection section, the Message Flood subsection, and the desired

Flood Threshold subsection.

4. Next to DLP Archive, select First message only from the dropdown menu.

5. Select OK.

 

Order of operations: flood checking before duplicate checking

Although duplicate checking involves only examination and comparison of message contents and not the sender or recipient, and flood checking involves only totalling the number of messages sent by each subscriber regardless of the message content, there are times when a selection of messages exceed both flood and duplicate thresholds.

The Carrier-enabled FortiGate unit checks for message floods before checking for duplicate messages. Flood checking is less resource-intensive and if the flood threshold invokes a Block action, the blocked messages are stopped before duplicate checking occurs. This saves both time and FortiOS Carrier system resources.

The duplicate scanner will only scan content. It will not scan headers. Content must be exactly the same. If there is any difference at all in the content, it will not be con- sidered a duplicate.

 

Bypassing message flood protection based on user’s carrier endpoints

You can use carrier endpoint filtering to exempt MMS sessions from message flood protection. Carrier endpoint filtering matches carrier endpoints in MMS sessions with carrier endpoint patterns.

If you add a carrier endpoint pattern to a filter list and set the action to exempt from mass MMS, all messages from matching carrier endpoints bypass message flood protection. This allows legitimate bulk messages, such as system outage notifications, to be delivered without triggering message flood protection.

For more information on carrier endpoints, see the User Authentication chapter of the FortiOS Handbook.

 

Configuring message flood detection

To have the Carrier-enabled FortiGate unit check for message floods, you must first configure the flood threshold in an MMS profile, select the MMS profile in a security policy. All the traffic examined by the security policy will be checked for message floods according to the threshold values you set in the MMS profile.

 

Configure the MMS profile – web-based manager

1. Go to Firewall Objects > MMS Profile.

2. If you are editing an MMS profile, select the Edit icon of the MMS profile.

If you are creating a new MMS profile, select Create New and enter a profile name.

3. Expand MMS Bulk Email Filtering Detection.

4. Expand Message Flood.

5. Expand Flood Threshold 1.

6. Select the Enable check box for MM1 messages, MM4 messages, or both.

7. In the Message Flood Window field, enter the length of time the Carrier-enabled FortiGate unit will keep track of the number of messages each subscriber sends.

If the Carrier-enabled FortiGate unit detects the quantity of messages specified in the Message Flood Limit sent during the number of minutes specified in the Message Flood Window, a message flood is in progress.

8. In the Message Flood Limit field, enter the number of messages required to trigger the flood.

9. In the Message Flood Block Time field, enter the length of time a user will be blocked from sending messages after causing the message flood.

10. Select the message flood actions the Carrier-enabled FortiGate unit will take when the message flood is detected.

11. Select OK.

 

Configure the security policy – web-based manager

1. Go to Policy.

2. Select the Edit icon of the security policy that controls the traffic in which you want to detect message floods.

3. Select the MMS Profile check box to enable the use of a protection profile.

4. Select the MMS protection profile from the list.

5. Select OK.

Notifying message flood senders and receivers

The FortiOS Carrier unit does not send notifications to the sender or receiver that cause a message flood. If the sender or receiver is an attacker and is explicitly informed that they have exceeded a message threshold, the attacker may try to determine the exact threshold value by trial and error and then find a way around flood protection. For this reason, no notification is set to the sender or receiver.

However, FortiOS Carrier does have replacement messages for sending reply confirmations to MM1 senders and receivers and for MM4 senders for blocked messages identified as message floods. For information about how FortiOS Carrier responds when message flood detection blocks a message, see and MMS duplicate messages and message floods.

 

Responses to MM1 senders and receivers

When the FortiOS Carrier unit identifies an MM1 message sent by a sender to an MMSC as a flood message and blocks it, the FortiOS Carrier unit returns a message submission confirmation (m-send.conf) to the sender — otherwise the sender’s handset would keep retrying the message. The m-send.conf message is sent only when the MM1 message flood action is set to Block. For other message flood actions the message is actually delivered to the MMSC and the MMSC sends the m-send.conf message.

You can customize the m-send.conf message by editing the MM1 send-conf flood message MM1 replacement message (from the CLI the mm1-send-conf-flood replacement message). You can customize the response status and message text for this message. The default response status is “Content not accepted”. To hide the fact that FortiOS Carrier is responding to a flood, you can change the response status to “Success”. The default message text informs the sender that the message was blocked. You could change this to something more generic.

For example, the following command sets the submission confirmation response status to “Success” and changes the message text to “Message Sent OK”:

config system replacemsg mm1 mm1-send-conf-flood set rsp-status ok

set rsp-text “Message Sent OK”

end

When the FortiOS Carrier unit identifies an MM1 message received by a receiver from an MMSC as a flood message and blocks it, the FortiOS Carrier unit returns a message retrieval confirmation (m-retrieve.conf) to the sender (otherwise the sender’s handset would keep retrying the message). The m-retrieve.conf message is sent only when the MM1 message flood action is set to Block. For other message flood actions the message is actually delivered to the receiver, so the MMSC sends the m-retrieve.conf message.

You can customize the m-retrive.conf message by editing the MM1 retrieve-conf flood message MM1 replacement message (from the CLI the mm1-retr-conf-flood replacement message). You can customize the class, subject, and message text for this message.

For example, you could use the following command make the response more generic:

config system replacemsg mm1 mm1-retr-conf-flood set subject “Message blocked”

set message “Message temporarily blocked by carrier”

end

 

Forward responses for MM4 message floods

When the FortiOS Carrier unit identifies an MM4 message as a flood message and blocks it, the FortiOS Carrier unit returns a message forward response (MM4_forward.res) to the forwarding MMSC (otherwise the forwarding MMSC would keep retrying the message). The MM4_forward.res message is sent only when the MM4 message flood action is set to Block and the MM4-forward.req message requested a response. For more information, see and MMS duplicate messages and message floods.

You can customize the MM4_forward.res message by editing the MM4 flood message MM4 replacement message (from the CLI the mm4-flood replacement message). You can customize the response status and message text for this message. The default response status is “Content not accepted” (err-content-not- accept). To hide the fact that the FortiOS Carrier unit is responding to a flood, you can change the response status to “Success”. The default message text informs the sender that the message was blocked. You could change this to something more generic.

For example, the following command sets the submission confirmation response status to “Success” and changes the message text to “Message Sent OK” for the MM4 message forward response

config system replacemsg mm4 mm4-flood set rsp-status ok

set rsp-text “Message Forwarded OK”

end

Notifying administrators of floods

You can configure alert notifications for message floods by selecting the Alert Notification message flood action. The FortiOS Carrier unit sends alert notifications to administrators using the MM1, MM3, MM4, or MM7 content interface. To send an alert notification you must configure addresses and other settings required for the content interface.

For example, to send notifications using the MM1 content interface you must configure a source MSISDN, hostname, URL, and port to which to send the notification. You can also configure schedules for when to send the notifications.

Finally you can add multiple MSISDN numbers to the MMS protection profile and set which flood thresholds to send to each MSISDN.

 

Example — three flood threshold levels with different actions for each threshold

You can set up to three threshold levels to take different actions at different levels of activity.

The first example threshold records log messages when a subscriber’s handset displays erratic behavior by sending multiple messages using MM1 at a relatively low threshold. The erratic behavior could indicate a problem with the subscriber’s handset. For example, you may have determined for your network that if a subscriber sends more the 45 messages in 30 minutes that you want to record log messages as a possible indication or erratic behavior.

From the web-based manager in an MMS profile set message Flood Threshold 1 to:

Enable                                        Selected

Message Flood Window          30 minutes

Message Flood Limit               45

Message Flood Action             Log

From the CLI:

config firewall mms-profile edit profile_name

config flood mm1

set status1 enable set window1 30

set limit1 45 set action1 log

end end

 

Set a second higher threshold to take additional actions when a subscriber sends more that 100 messages in 30 minutes. Set the actions for this threshold to log the flood, archive the message that triggered the second threshold, and block the sender for 15 minutes.

From the web-based manager in an MMS profile set message Flood Threshold 2 to:

 

Enable                                        Selected

Message Flood Window          30 minutes

Message Flood Limit               100

Message Block Time                15 minutes

Message Flood Action             Log, DLP archive First message only, Block

 

From the CLI:

config firewall mms-profile edit profile_name

config flood mm1

set status2 enable set window2 30

set limit2 100

set action2 block log archive-first set block-time2 15

end end

 

Set the third and highest threshold to block the subscriber for an extended period and sand an administrator alert if the subscriber sends more than 200 messages in 30 minutes. Set the actions for this threshold to block the sender for four hours (240 minutes), log the flood, archive the message that triggered the third threshold, and send an alert to the administrator.

From the web-based manager in an MMS profile set message Flood Threshold 3 to:

Enable                                        Selected

Message Flood Window          30 minutes

Message Flood Limit               200

Message Block Time                240 minutes

Message Flood Action             Log, Block, Alert Notification

Because you have selected the Alert Notification action you must also configure alert notification settings. For this example, the source MSISDN is 5551234—telephone number 555-1234. When administrators receive MMS messages from this MSIDSN they can assume a message flood has been detected.

In this example, alert notifications are sent by the FortiOS Carrier unit to the MMSC using MM1. The host name of the MMSC is mmscexample, the MMSC URL is /, and the port used by the MMSC is 80. In this example, the alert notification window starts at 8:00am and extends for eight hours on weekdays (Monday-Friday) and the minimum interval between message flood notifications is two hours.

Source MSISDN                         5551234

Message Protocol                     MM1

Hostname                                   mmscexample

URL                                             /

Port                                             80

Notifications Per Second         0

Limit

Window Start Time                   8:00

Window Duration                      8:00

Day of Week                               Mon, Tue, Wed, Thu, Fri, Sat

Interval                                       2 hours

From the CLI:

config firewall mms-profile edit profile_name

config notification alert-flood-1 set alert-src-msisdn 5551234 set set msg-protocol mm1

set mmsc-hostname mmscexample set mmsc-url /

set mmsc-port 80 set rate-limit 0

set tod-window-start 8:00

set tod-window-duration 8:00

set days-allowed monday tuesday wednesday thursday friday set alert-int 2

set alert-int-mode hours

end

You must also add the MSISDNs of the administrators to be notified of the message flood. In this example, the administrator flood threshold 3 alert notifications are sent to one administrator with MSISDN 5554321.

To add administrator’s MSISDNs for flood threshold 3 from the web-based manager when configuring a protection profile, select MMS Bulk Email Filtering Detection > Recipient MSISDN > Create New.

MSISDN                     5554321

Flood Level 3           Select

 

From the CLI:

config firewall mms-profile edit profile_name

config notif-msisdn edit 5554321

set threshold flood-thresh-3

end