Logging and monitoring

This section provides some general logging and monitoring procedures for VPNs.

The following topics are included in this section:

Monitoring VPN connections

VPN event logs

Monitoring VPN connections

You can use the monitor to view activity on IPsec VPN tunnels and to start or stop those tunnels. The display provides a list of addresses, proxy IDs, and timeout information for all active tunnels.

Monitoring connections to remote peers

The list of tunnels provides information about VPN connections to remote peers that have static IP addresses or domain names. You can use this list to view status and IP addressing information for each tunnel configuration. You can also start and stop individual tunnels from the list.

To view the list of static-IP and dynamic-DNS tunnels go to Monitor > IPsec Monitor.

Monitoring dialup IPsec connections

The list of dialup tunnels provides information about the status of tunnels that have been established for dialup clients. The list displays the IP addresses of dialup clients and the names of all active tunnels. The number of tunnels shown in the list can change as dialup clients connect and disconnect.

To view the list of dialup tunnels go to Monitor > IPsec Monitor.

If you take down an active tunnel while a dialup client such as FortiClient is still connected, FortiClient will continue to show the tunnel connected and idle. The dialup client must disconnect before another tunnel can be initiated.

The list of dialup tunnels displays the following statistics:

• The Name column displays the name of the tunnel.
• The meaning of the value in the Remote gateway column changes, depending on the configuration of the network at the far end:
• When a FortiClient dialup client establishes a tunnel, the Remote gateway column displays either the public IP address and UDP port of the remote host device (on which the FortiClient Endpoint Security application is installed), or if a NAT device exists in front of the remote host, the Remote gateway column displays the public IP address and UDP port of the remote host. l When a FortiGate dialup client establishes a tunnel, the Remote gateway column displays the public IP address and UDP port of the FortiGate dialup client.
• The Username column displays the peer ID, certificate name, or XAuth user name of the dialup client (if a peer ID, certificate name, or XAuth user name was assigned to the dialup client for authentication purposes).
• The Timeout column displays the time before the next key exchange. The time is calculated by subtracting the time elapsed since the last key exchange from the keylife.
• The Proxy ID Source column displays the IP addresses of the hosts, servers, or private networks behind the FortiGate unit. A network range may be displayed if the source address in the security encryption policy was expressed as a range of IP addresses.
• The meaning of the value in the Proxy ID Destination column changes, depending on the configuration of the network at the far end: l When a FortiClient dialup client establishes a tunnel:
• If VIP addresses are not used and the remote host connects to the Internet directly, the Proxy ID Destination field displays the public IP address of the Network Interface Card (NIC) in the remote host.
• If VIP addresses are not used and the remote host is behind a NAT device, the Proxy ID Destination field displays the private IP address of the NIC in the remote host.
• If VIP addresses were configured (manually or through FortiGate DHCP relay), the Proxy ID Destination field displays either the VIP address belonging to a FortiClient dialup client, or a subnet address from which VIP addresses were assigned. l When a FortiGate dialup client establishes a tunnel, the Proxy ID Destination field displays the IP address of the remote private network.

VPN event logs

You can configure the FortiGate unit to log VPN events. For IPsec VPNs, Phase 1 and Phase 2 authentication and encryption events are logged. For information about how to interpret log messages, see the FortiGate Log Message Reference.

Logging VPN events

1. Go to Log & Report > Log Settings.
2. Verify that the VPN activity event option is selected.
3. Select Apply.

Viewing event logs

1. Go to Log & Report > VPN Events.
2. Select the Log location.

Sending tunnel statistics to FortiAnalyzer

By default, logged events include tunnel-up and tunnel-down status events. Other events, by default, will appear in the FortiAnalyzer report as “No Data Available”. More accurate results require logs with action=tunnelstats, which is used in generating reports on the FortiAnalyzer (rather than the tunnel-up and tunnel-down event logs). The FortiGate does not, by default, send tunnel-stats information.

To allow VPN tunnel-stats to be sent to FortiAnalyzer, configure the FortiGate unit as follows using the CLI:

config system settings set vpn-stats-log ipsec ssl set vpn-stats-period 300 end