Introduction

This document describes what you need to know to get started using a FortiGate-7000 product. Also included are details about CLI commands that are specific to FortiGate-7000 products.

This FortiOS Handbook chapter contains the following sections:

FortiGate-7000 overview provides a quick overview of FortiGate-7000 components.

Getting started with FortiGate-7000 describes how to get started with managing and configuring your FortiGate7000 product.

FortiGate-7000 Load balancing commands describes FortiGate-7000 load balancing CLI commands.

What’s new in for FortiGate-7000 v5.4.5

The following new features have been added to FortiGate-7000 v5.4.5.

M1 and M2 interfaces can use different VLANs for heartbeat traffic (408386)

The M1 and M2 interfaces can be configured to use different VLANs for HA heartbeat traffic.

The following command now configures the VLAN used by the M1 interface (default 999):

config system ha set hbdev-vlan-id 999

end

The following new command configures the VLAN used by the M2 interface (default 1999):

config system ha set hbdev-second-vlan-id 1999

end

GTP load balancing

GTP load balancing is supported for FortiGate-7000 configurations licensed for FortiOS Carrier. You can use the following command to enable GTP load balancing. This command is only available after you have licensed the FortiGate-7000 for FortiOS Carrier.

config load-balance setting set gtp-load-balance enable

end

FSSO user authentication is synchronized

FSSO user authentication is synchronized to all FIM and FPM modules. FSSO users are no longer required to reauthenticate when sessions are processed by a different FIM or FPM module.

What’s new in for FortiGate-7000 v5.4.5                                                                                                Introduction

HA Link failure threshold changes (422264 )

The link failure threshold is now determined based on the all FIM modules in a chassis. This means that the chassis with the fewest active links will become the backup chassis.

FortiGate-7000s running FortiOS v5.4.5 can be configured as dialup IPsec VPN servers

The following shows how to setup a dialup IPsec VPN configuration where the FortiGate-7000 running v5.4.5 acts as a dialup IPsec VPN server.

Configure the phase1, set type to dynamic.

config vpn ipsec phase1-interface edit dialup-server set type dynamic set interface “v0020” set peertype any set psksecret < password>

end

Configure the phase 2, to support dialup IPsec VPN, set the destination subnet to 0.0.0.0 0.0.0.0.

config vpn ipsec phase2-interface edit dialup-server set phase1name dialup-server set src-subnet 4.2.0.0 255.255.0.0 set dst-subnet 0.0.0.0 0.0.0.0

end

To configure the remote FortiGate as a dialup IPsec VPN client

The dialup IPsec VPN client should advertise its local subnet(s) using the phase 2 src-subnet option.

If there are multiple local subnets create a phase 2 for each one. Each phase 2 only advertises one local subnet to the dialup IPsec VPN server. If more than one local subnet is added to the phase 2, only the first one is advertised to the server.

Dialup client configuration:

config vpn ipsec phase1-interface

Introduction                                                                                                What’s new in for FortiGate-7000 v5.4.5

edit “to-fgt7k” set interface “v0020” set peertype any set remote-gw 1.2.0.1 set psksecret <password>

end

config vpn ipsec phase2-interface edit “to-fgt7k” set phase1name “to-fgt7k” set src-subnet 4.2.6.0 255.255.255.0 set dst-subnet 4.2.0.0 255.255.0.0

next edit “to-fgt7k-2” set phase1name “to-fgt7k” set src-subnet 4.2.7.0 255.255.255.0 set dst-subnet 4.2.0.0 255.255.0.0 end

Licenses, Device Registration, and Support                                                                         FortiGate-7000 overview